IBM VIOS

Please check this page first: http://www.getshifting.com/wiki/aixvios

Please do not use cfgassist to assign IP address which never works for me.

To assign a IP address, please use this command or use smit:

mktcpip -hostname vios -inetaddr 10.10.10.10 -interface en0 -netmask 255.255.0.0 -gateway 10.10.10.1 -nsrvaddr 10.10.10.100 -nsrvdomain company.local -start

 
To enable the regular AIX shell, please type the following command:

oem_setup_env

After you are in the regular AIX shell,
 
To find which NIC has the link:

entstat -d en[0-9]

 
To run the smit:

smit

 
To find out network link info:
prtconf to find network card info
 
# entstat -dt en4
-------------------------------------------------------------
ETHERNET STATISTICS (en4) :
Device Type: 10 Gb Ethernet PCI Express Dual Port Adapter (7710008077108001)
Hardware Address: 00:c0:dd:15:b8:ec
Elapsed Time: 0 days 0 hours 0 minutes 0 seconds
Transmit Statistics:                          Receive Statistics:
--------------------                          -------------------
Packets: 0                                    Packets: 0
Bytes: 0                                      Bytes: 0
Interrupts: 0                                 Interrupts: 7
Transmit Errors: 0                            Receive Errors: 0
Packets Dropped: 0                            Packets Dropped: 0
                                              Bad Packets: 0
Max Packets on S/W Transmit Queue: 0        
S/W Transmit Queue Overflow: 0
Current S/W+H/W Transmit Queue Length: 0
Broadcast Packets: 0                          Broadcast Packets: 359768
Multicast Packets: 2689                       Multicast Packets: 31813
No Carrier Sense: 0                           CRC Errors: 0
DMA Underrun: 0                               DMA Overrun: 0
Lost CTS Errors: 0                            Alignment Errors: 0
Max Collision Errors: 0                       No Resource Errors: 0
Late Collision Errors: 0                      Receive Collision Errors: 0
Deferred: 0                                   Packet Too Short Errors: 0
SQE Test: 0                                   Packet Too Long Errors: 0
Timeout Errors: 0                             Packets Discarded by Adapter: 0
Single Collision Count: 0                     Receiver Start Count: 0
Multiple Collision Count: 0
Current HW Transmit Queue Length: 0
General Statistics:
-------------------
No mbuf Errors: 0
Adapter Reset Count: 0
Adapter Data Rate: 20000
Driver Flags: Up Broadcast Running
        Simplex 64BitSupport ChecksumOffload
        LargeSend DataRateSet
10 Gb Ethernet PCI Express Dual Port Adapter (7710008077108001) Specific Statistics:
------------------------------------------------------------------------------------
Link Status : Up
Media Speed Running: 10 Gbps Full Duplex
Flow Control Status: Standard Pause mode Enabled
        Flow Control Packets Transmitted: 0
        Flow Control Packets Received: 0
PCI Mode: PCI-Express x8
        Relaxed Ordering: Enabled
        MRR Size: 512
        MPS Size: 512
        Current Link Speed: 2.5 Gbps
Jumbo Frames: Disabled
TCP Segmentation Offload: Enabled
        TCP Segmentation Offload Packets Transmitted: 0
        TCP Segmentation Offload Maximum Packet Size: 0
Receive TCP Segment Aggregation: Enabled
        TCP Segment Aggregation Large Packets Created: 0
        TCP Packets Aggregated into Large Packets: 0
        TCP Segment Aggregation Average Packets Aggregated: 1
        TCP Segment Aggregation Maximum Packets Aggregated: 0
Small Buffer Cluster Pool Allocation Failures: 0
Large Buffer Cluster Pool Allocation Failures: 0
DCBX Status: Disabled
FCOE Priority: 0
FCOE Priority Collisions: 0

Comments

Popular posts from this blog

VIOS TIPs

Configure Solaris 10 LDOM on Solaris 11.4

Change P410i from HBA mode to Raid mdoe